Machine Bolts Specification | Machine Bolts - Machine Bolts Techinical Information | Machine Bolts Dimensions
red earth fasteners
red earth fasteners
Fasteners
  Types of Fasteners Fasteners Nuts Fasteners Screws Fasteners Washer Fasteners Bolts Fasteners Bolts  
YOU ARE HERE : Home : Products : Specification: Machine Bolts

Are You Looking Trusted Manufacturer & Suppliers of Machine Bolts | Machine Bolts + Ramesh Steel is Largest Manufacturer of All Types Fasteners in Mumbai India.

Click Here For : Fasteners Weight Calculator | Bolts Weight Calculator | Nuts Weight Calculator

Fasteners NutsFasteners NutsFasteners NutsFasteners Nuts

Machine Bolts - Cross Arm Bolts

Machine bolts are used to fasten wood to wood, wood to metal and metal to metal. Similar to a hex cap screw, a machine bolt will differ in these four ways: its point will not be chamfered or rounded; it will be available in larger sizes (diameters); it will not have an underhead washer bearing surface; and it will be manufactured to less exacting standards. Depending on head style, machine bolts are also known as:
hex bolts, square bolts.

They are used with nuts and internally threaded (tapped) holes.

Machine Bolt, Square HeadThreads are standard right-hand and often Unified inch coarse series (UNC, Unified National Coarse). Short lengths are fully threaded while longer lengths follow a standard formula: for bolts 6" and shorter, the minimum threaded length is two times the basic thread diameter plus 1/4", and for lengths greater than 6", two times the diameter plus 1/2".

Typically, machine bolt sizes range from 1/4" to 1 1/4" for square heads and 3/8" to 1 3/4" in diameter for hex heads, and lengths span from about 3/4" to 18" for square and 6 1/2" to 24" for hex heads. Measure length from under the head to the threaded end of the bolt.

Both square and hex heads are available. The size of the head varies with the size of the machine bolt. Since it is externally wrenched, sufficient space around the head must be allowed for wrench clearance. Tables 1 and 2 list head width across flats, which is wrench size, and across corners, head height and minimum threaded length.

Machine bolts are available in Grade 2. Steel is the standard material, and plain finish, which lacks a surface treatment to inhibit rust, is common.

When installing in wood, drill holes no more than 1/16" larger than the bolt size. If you drill into an untreated area of treated lumber, saturate the hole with a preservative to prevent the migration of decay fungi. In addition, always use a large diameter washer under the head and nut to distribute clamping force over a larger area and to minimize compression of the wood. Bolts should be retightened after about a year then checked yearly for tightness.

Machine and lag bolts are the preferred fasteners for fastening heavy wood members in structures. Machine bolts, in comparison to lag bolts, offer increased rigidity and load-carrying capacity but require a through-hole and access to both sides of the joint for wrenching the head and nut. Lag bolts, despite their lower lateral strength, are useful when access to one side of the joint is limited, the appearance of a nut is undesirable or through-bolt length is excessive. When compared to carriage bolts, machine bolts are available in larger sizes and are often preferable because carriage bolts are not designed to accept a washer under their head. However, carriage bolts are available in hot dip galvanized and stainless steel types.

Refer to American Society of Mechanical Engineers Standard ASME B18.2.1, Square and Hex Bolts and Screws, for specifications relating to machine bolts.

Dimensions of Hex Head Machine Bolt

Nominal Size or Basic Product Diameter E F G H R L
Full·Size Body Diameter Width Across Flats Width Across Corners Head Height Radius of Fillet Thread Length for Bolt Lengths
6 in.and Shorter Over 6 in.
Max Min Basic Max Min Max Min Basic Max Min Max Min Nom Nom
1/4 0.2500 0.260 0.237 7/16 0.438 0.425 0.505 0.484 11/64 0.188 0.150 0.03 0.01 0.750 1.000
5/16 0.3125 0.324 0.298 1/2 0.500 0.484 0.577 0.552 7/32 0.235 0.195 0.03 0.01 0.875 1.125
3/8 0.3750 0.388 0.360 9/16 0.562 0.544 0.650 0.620 1/4 0.268 0.226 0.03 0.01 1.000 1.250
7/16 0.4375 0.452 0.421 5/8 0.625 0.603 0.722 0.687 19/64 0.316 0.272 0.03 0.01 1.125 1.375
1/2 0.5000 0.515 0.482 3/4 0.750 0.725 0.866 0.826 11 /32 0.364 0.302 0.03 0.01 1.250 1.500
5/8 0.6250 0.642 0.605 15/16 0.938 0.906 1.083 1.033 27/64 0.444 0.378 0.06 0.02 1.500 1.750
3/4 0.7500 0.768 0.729 1-1/8 1.125 1.088 1.299 1.240 1/2 0.524 0.455 0.06 0.02 1.750 2.000
7/8 0.8750 0.895 0.852 1-5/16 1.312 1.269 1.516 1.447 37/64 0.604 0.531 0.06 0.02 2.000 2.250
1 1.0000 1.022 0.976 1-1/2 1.500 1.450 1.732 1.653 43/64 0.700 0.591 0.09 0.03 2.250 2.500
1-1/8 1.1250 1.149 1.098 1-11/16 1.688 1.631 1.949 1.859 3/4 0.780 0.658 0.09 0.03 2.500 2.750
1-1/4 1.2500 1.277 1.223 1-7/8 1.875 1.812 2.165 2.066 27/32 0.876 0.749 0.09 0.03 2.750 3.000
1-3/8 1.3750 1.404 1.345 2-1/16 2.062 1.994 2.382 2.273 29/32 0.940 0.810 0.09 0.03 3.000 3.250
1-1/2 1.5000 1.531 1.470 2-1/4 2.250 2.175 2.598 2.480 1 1.036 0.902 0.09 0.03 3.250 3.500
1-5/8 1.6250 1.658 1.591 2-7/16 2.438 2.356 2.815 2.616 1-3/32 1.116 0.978 0.09 0.03 3.500 3.750
1-3/4 1.7500 1.785 1.716 2-5/8 2.625 2.538 3.031 2.893 1-5/32 1.196 1.054 0.12 0.04 3.750 4.000
1-7/8 1.8750 1.912 1.839 2-13/16 2.812 2.719 3.248 3.099 1-1/4 1.276 1.130 0.12 0.04 4.000 4.250
2 2.0000 2.039 1.964 3 3.000 2.900 3.464 3.306 1-11/32 1.388 1.175 0.12 0.04 4.250 4.500
2-114 2.2500 2.305 2.214 3-3/8 3.375 3.262 3.897 3.719 1-1/2 1.548 1.327 0.19 0.06 4.750 5.000
2-1/2 2.5000 2.559 2.461 3-3/4 3.750 3.625 4.330 4.133 1-21/32 1.708 1.479 0.19 0.06 5.250 5.500
2-3/4 2.7500 2.827 2.711 4-1/8 4.125 3.988 4.763 4.546 1-13/16 1.869 1.632 0.19 0.06 5.750 6.000
3 3.0000 3.081 2.961 4-1/2 4.500 4.350 5.196 4.959 2 2.060 1.815 0.19 0.06 6.250 6.500
3-1/4 3.2500 3.335 3.210 4-7/8 4.875 4.712 5.629 5.372 2-3/16 2.251 1.936 0.19 0.06 6.750 7.000
3-1/2 3.5000 3.589 3.461 5-1/4 5.250 5.075 6.062 5.786 2-5/16 2.380 2.057 0.19 0.06 7.250 7.500
3-3/4 3.7500 3.858 3.726 5-5/8 5.625 5.437 6.495 6.198 2-1/2 2.572 2.241 0.19 0.06 7.750 8.000
4 4.0000 4.111 3.975 6 6.000 5.800 6.928 6.612 2-11/16 2.764 2.424 0.19 0.06 8.250 8.500
See Paras. 3.4, 3.5 2.1.2     3.7

Machine Bolts Price

grade 8.8 hex head machine bolts
FOB Price: US$0.01 to 3 / Piece

din933 grade 8.8 M16 GRADE 4.8 Hex Bolt 8.8 Black For Machine m24 hex bolt
FOB Price: US$900 to 1450 / Ton

Hex bolt M16/ DIN933 &931 /machine bolt /bolt and nut
FOB Price: US$0.1 to 1 / Piece

For quick Quote on Machine Bolts, please contact our Sales team.

 

 

Email : sales@rameshgroup.com, info@rameshgroup.com, rameshsteel44@yahoo.co.in
 

 

SEND ONLINE INQUIRY


WE DELIVER TO FOLLOWING COUNTRIES & CITIES WITH TIME ESTIMATE

MIDDLE EAST
Country
Deliver Days Port Name
Malaysia 10 - 20 Days Port of Klang, Malaysia - Penang Port, Malaysia
Singapore 10 - 20 Days Northport , Malaysia - Westports, Malaysia
Thailand 20-30 Days Port of Laem Chabang, Thailand
Philippines 20-30 Days Port of Manila - Port of Jordan, Philippines
Indonesia 25-40 Days Jakarta Tanjung Priok Seaport indonesia
Sri Lanka 10-15 Days Port of Colombo

Bangladesh

5-10 Days The Port of Chittagong (Bangladesh)
UAE 5-10 Days Port of Mina Jebel Ali (Jebel Ali - Dubai ) , United Arab Emirates & Port Zayed (Mina Zayed), United Arab Emirates
Saudi Arabia 10-20 Days Jeddah Islamic Port, Saudi Arabia
Turkey 20-30 Days Haydarpasa, Izmir and Mersin Port - Port of Ambarli, Turkey
Qatar 8 - 12 Days Port of Doha, Qatar & Port of Al Wakrah, Qatar
Oman 5 - 10 Days Port Of Sohar - Oman , Port of Muscat - Oman
Kuwait 8 - 15 Days Port of Kuwait, Kuwait
Yemen 8 - 15 Days Port of Aden, Yemen
Jordan 15 - 20 Days Port of Aqaba, Jordan
Cyprus 16 - 20 Days Famagusta Port, Cyprus

 

AFRICAN 
Countries Port
Deliver Days Port Name
Nigeria 35 - 40 days Tin Can Island Port Complex, Nigeria
Algeria 35 - 40 days Port of Alger, Algeria - Port of Bejaia, Algeria - Port of oran, Algeria - Port of ghazaouet, Algeria
Angola 35 - 40 days Port of Luanda, Angola
South Africa 20 - 30 days Port Elizabeth, South Africa
Libya 18 - 20 Port of Benghazi, Libya
Egypt 15 - 20 Days Port of Damietta, Egypt
Sudan 10-15 Days Port of Sudan, Sudan
Equatorial Guinea 35 - 40 days Port of Malabo, Equatorial Guinea - Port of Bata, Equatorial Guinea
The Republic Of Congo 35 - 40 days Port of Matadi, Congo - Kinshasa
Gabon 35 - 40 days Port of Owendo, Gabon

Duplex Steel Fasteners Manufacturers India, Nut Bolts - Screws Washers, manufacturers, suppliers, exporters, distributors, traders, stockholder, wholesaler, manufacturer, supplier, exporter, distributor, trader, stockist, India


copyright (c) 2011 by Ramesh Group, all rights reserved.  |  Blog | Website Design & Seo by www.mesotek.com